Quick update

So, I had the bike completed for over 2 month now. I haven't had a chance to take it out for a proper ride yet apart from some quick ones around the Phoenix Park. This was mainly due to the fact that the handlebars were too big for me and that I wasn't confident enough to ride the bike without being able to use the brake comfortably and safely.
I ordered new handlebars and a stem from www.Allterraincycles.co.uk. These were the Bontrager SSR OS Stem and the Bontrager Race VR-S Road Bar. The stem was a short 60mm stem to accommodate me better on the frame and the handlebars were the short drop handlebars with a short reach (70mm) I found out about these from trying out the girlfriends new bike which was a Trek Lexa and it had the same handlebars on it. I fitted them last night on the bike along with a quill adapter which was bought from Joe Dalys Cycle in Dumdrum where David was extremely helpful in acquiring this item as it was a bit of an unusual size. Took the bike out for a quick spin today in Phoenix park again and it felt just right like Goldilocks would say. I am very pleased with the result and feel that the bike is finally the way I expected it to be.


Here is a quick picture of the new handlebars:

More updates to follow as I will be bringing the bicycle down to Cork this coming week and will need to find new routes over there. If anyone has any suggestions for Cork please let me know. Thanks :)

Finishing it all up

Today I went into the shop to put on more parts on the bike. I didn't know much about putting on the STI levers. cables, brakes etc and I was very lucky to have Gabriel and Gareth to help me out. I was being the little helper as I wouldn't have been able to do it all by myself now.
We had to cut the forks by a couple of centimeters and that took a couple of tries to get it right as me and Gabriel couldn't find the mark that was made on the metal. In the end we managed to get it right and the handlebars went in without too much trouble. Ok, maybe with a little bit of help from the hammer.

This was Gareth and Gabriel messing about while getting the parts on the bike.

Next went on the gear/brake levers on the handlebars along with the cables which needed some gentle cohersing especially the cables for the front mech. Gabriel found a way to make it work and we were in business.

After that, the rear mech, rear hanger and crankset went in. I took off the chain protector off the outer chainring as it looked a bit silly. Those went up without any trouble onto the frame.

Sprocket, front and back wheels went on along with the chain and after some tweaking by Gabriel, the gear changes were as smooth as butter. The handle bartape went up easily and it looked the part. Also, the seat looked even better today.

And this is the final result with the finished bicycle. It looks pretty cool I think and tomorrow I will go have a cycle on it to test it all out and see how it handles and what needs to be tweaked as I know there will be some tiny adjustments that will be required.

But for tonight, it will hang by the ceiling in the shop till I get to see her tomorrow and go for a test ride.

Build it up

Today I started to put the parts on the bicycle after getting the frame unwrapped from the masking tape and paper. The frame and fork had been left the to cure over the last four days and the end result was very decent.

I was really happy how it all turned out and the orange and black bit on the horizontal tube looked pretty cool.
After getting the box of parts, Gabriele, Gareth and Anne helped me put on the headset onto the fork and frame. I then put on the seat, seat post, front brake calipers and rear brake calipers onto the frame. Getting the seat and seatpost was the most difficult task for me as the metal frame of the seat made it really tight to access. But I managed it in the end and I must say that seat looks gorgeous and looks more expensive that it really was. All the new parts that I bought were from Ribble Cycles (www.ribblecycles.co.uk), which had a 20% off offer a while ago and were very prompt in their delivery and charges. It took seven days to get to me but I didn't mind as their delivery charges were very reasonable and with the 20% off offer, suited my shoe string budget for this project.

This is the progress so far and tomorrow once we get a hacksaw, we are going to cut the stem to size after measuring it properly as this is a precision job. After that, I will keep on putting the rest of the parts until I get to the wheels, which have been ordered, but have not arrived yet. I reckon it will be a very exciting day tomorrow as I get to open the plastic bags containing the parts and getting them onto the bike. Roll on tomorrow :)

Mask away

Yesterday I started painting the orange and black accents on the bicycle frame. It took ages to mask the right areas and get it ready for the layering of the paint. After wrapping up the frame with masking tape and paper, it looked a bit like a Christmas gift. I must admit, I was being my usual anal self when putting the masking paper and covering the parts. But I knew that taking my time and being meticulous now would make the end result worth it. 

Today I was so excited to see how the masking had worked out that I went to work on the bicycle. It was like Christmas morning unwrapping the paper and masking tape off the frame. It turned out as good as I could have hoped. There were a couple of blemishes and rough spots, but overall not a bad job for my first frame painting job. I then put on a layer of clear coat onto it but was a bit disappointed with the nozzle on the spray can. It didn't diffuse the clear as evenly as the nozzle on the cans of Montana 94 paint. As a result, there were a couple of places on the frame where the clear coat dripped and this ended up messing it a bit. But it's not too big of a problem as it can be easily remedied with some wet sanding. I left the frame and forks to cure and will be back to have a look at the end result come Monday. Sadly I forgot to bring the camera with me but pictures will soon follow.

Azul Perseo the first

Yesterday I spray painting the frame with the first coat of Azul Perseo colour and left it to dry overnight. When I went to the shop today, the result was quite good and I got onto putting another coat of paint onto the frame and also the forks which I left lastly to paint. I used the rest the can of paint today and managed to get two full coats on the frame and forks, which is was very good for me as the shop where I got the cans of Montana 94 from had run out of this particular colour and that they would only be getting it back in supply in about two to three weeks. This would have actually stop the progress of the bike build completely as I would not have been able to put any parts on the bicycle. In the end, the one can of spray paint was just enough and tomorrow I can start layering the Negro (Black) and Mandarina (Orange) colour onto the frame and forks in the way is similar to the Baum bicycle after getting some thin masking tape from Lenehans.
Here is the progress of the day so far.

Forks, more primer and a paint scheme

Yesterday Gareth gave me a set of forks for that fit the bicycle. I forgot to take a picture of it but here it is in all its glory.

Gareth is a total legend for hooking me up with these forks as I had tried pretty much every fork that was in the shop and none of them would fit on the bicycle frame as they were either too long or too short. But this one was just right like Goldilocks said. On top of that, these forks came with a pair of cantilever brakes which are superior to the original ones on the bike.
After cleaning up the forks and taking off the brakes, I sanded it down with two different grits of sandpaper until the lacquer was off. Then I used masking tape to tape off the parts that I didn't want primer on and got to spraying the forks with two layers of primer. It was a relatively easy and quick job as I had got lots of practice from the day before using the can of primer on the frame. The end result was a pair of forks with two coats of primer and no blemishes that I left to dry out on the line that we hang the frames.

Also today I put another coat of primer on the frame and the process was a bit easier than yesterday. Managed not to mess up and the frame looks ready to be painted. I left it to dry overnight on the hang line along with the other frames that have been painted in the shop.

Before I went to the shop today, I stopped by All City Records (http://shop.all-cityrecords.com/) in Temple Bar to pick up some spray paint for the bicycle. Montana-94 was recommended to me by the guys in Rothar as they use it regularly to paint bicycle frames. I ended up getting three cans for the colour scheme that I intend on putting onto the bike. I got Mandarina(Orange), Azul Perseo(Blue) and Negro(Black) and had a nice chat with the sales guy there who helped me get the right colours from the picture I had on the computer. I forgot to get his name and have to thank him for helping me out as I wouldn't have able to get the right colours had he not been there to lend me a hand.
The cans of Montana 94 are below and I think they look pretty cool.

The colour scheme that I have decided for the bicycle is based on the 1970's Porsche with the Gulf Oil livery. Hopefully, the end result of me painting the bike frame will be something like this:

I know it will not be exactly like that but I am hoping with a lot of work, it will turn out as close as I can get to the above picture without the Baum logo on the underside of the frame and the inside of the forks. Reckon with a lot of patience and masking tape, it will end up looking semi-decent. Bring on the first coat of paint tomorrow.

Here comes the paint

Today, I had a stab at painting the frame with the first layer of primer. Firstly I had to sand down the frame with some smooth sandpaper as over the last few days the frame picked up a bit of rust due to the dampness in the shop. After that, I cleaned the frame with a cloth and some thinner so that the primer would adhere properly to the frame. Next came shaking the can of primer for about one minute and then getting some gloves on so as not to end up with hands covered with grey paint. Gabrielle then showed me how to apply the paint onto the frame. Confident short bursts from the can of primer to avoid dribbling of the paint and keeping the motion fluid helped in getting a nice even coat of primer all over the frame. The whole process took about one hour as I was taking my time and had to wait for the paint to dry.I then got working on the underside of the frame as I had it on a box in the hallway, with the door propped open so that I didn't die(or get high) from the paint fumes.
In the end, I was quite pleased with the result as the primer was uniform all over the frame and there was only one slight imperfection which will be easily corrected with some sandpaper tomorrow before the next coat of primer is applied.

Tomorrow, I hope to go to All City Records in Temple Bar to buy the spray can paint (Montana 94) that I will be using to colour the frame. I have decided to go with a light blue paint with orange and black accents around the frame as an tribute to the Porsche 917 from the 1970's with the Gulf Oil livery. I have found a couple of examples on the net and it involves a lot of work but the end result is really cool from what I have seen. I know it will not be to the taste of a lot of people, but the colour scheme speaks to me as I am a big racing fan and I think that livery is quite iconic. Let's hope it turns out the way I image it :)